Note · 11 November 2026

Lyophilized Peptides: What the Powder Holds and What Changes It

Lyophilised means freeze-dried: frozen, then dried under vacuum. The powder holds the peptide with its counter-ion, residual water and any excipient. In measured studies, water left in or taken up by the solid lowered its glass transition and sped chemical degradation, though drier was not always more stable, and cakes that collapsed during drying held the proteins tested as stably as intact cakes.

The answer: freeze-dried, not water-free

Lyophilised means freeze-dried. The Food and Drug Administration's inspection guide describes freezing, then primary drying, in which ice passes directly to vapour under vacuum, then secondary drying by desorption, together removing most of the water, not all of it. A lyophilised research peptide is the peptide with its counter-ion, residual water and any excipient. In measured studies, more water in the dried solid lowered its glass transition and sped deamidation and aspartate isomerisation, yet one antibody aggregated more, and one enzyme turned opalescent on reconstitution, when dried hardest. Amorphous solids took up water from rubber stoppers and humid air, one peptide analogue to the point of deliquescence. Cakes that collapsed during drying held the proteins tested as stably as intact cakes; collapse that began in hot storage accompanied degradation.

Five of the six pages examined for this note stated that drying slows degradation. Their storage spans disagreed with one another and, like a figure of 17 years, traced to no study found; statements that the powder lacks water, that hydrolysis stops and that a solid cake signals quality were contradicted; and a residual moisture figure of under 1 to 3 per cent matched a published range for most biological products.

What the powder holds, and how its water was measured

A peptide powder weighs more than its peptide. This site's note on what HPLC purity measures recorded trifluoroacetate and water in the peptides it covered, whose peptide fractions ran from 530 to 896 mg/g. Formulated cakes add excipients, as in the studies below. A PubMed search on 11 November 2026 pairing residual moisture with peptide lyophilisates returned three records, none measuring a research-labelled vial.

May and colleagues, at the Center for Biologics Evaluation and Research, described in 1992 a revised regulation requiring each lot of a dried product to meet limits set by an approved method, no longer naming the gravimetric loss-on-drying method or a fixed 1.0 per cent limit. Their data on two vaccines came from gravimetric, coulometric Karl Fischer, thermogravimetric and thermogravimetric mass spectrometric methods, and they put residual moisture for most products at usually less than 1.0 to 3.0 per cent.

Water in the solid: rates measured against moisture

Water plasticises an amorphous solid, lowering the glass transition below which it is glassy. Lai and colleagues lyophilised the hexapeptide Val-Tyr-Pro-Asn-Gly-Ala in polyvinyl alcohol and polyvinylpyrrolidone in 1999 and held it at 50 degrees C: deamidation rose with water content as the glass transition fell, proceeded in the glassy state, and correlated with how far water had plasticised each matrix. This site's note on peptide storage recorded a factorial study on the same hexapeptide in which starting pH outweighed moisture.

Breen and colleagues lyophilised a humanised monoclonal antibody at 1 to 8 per cent residual moisture in 2001; its glass transition fell from 80 degrees C at 1 per cent to 25 degrees C at 8 per cent. Over 6 or 12 months at 5 to 50 degrees C, every formulation was stable at 5 degrees C, wetter cakes aggregated faster only above their glass transition, intermediate moisture resisted aggregation better than the driest cakes, and aspartate isomerisation rose with moisture above and below the glass transition.

Pikal and colleagues found significant methionine oxidation, asparagine deamidation and aggregation under most conditions in freeze-dried human growth hormone at 25 and 40 degrees C in 1992, with the effects of residual water and headspace oxygen depending on formulation: with little of either, a glycine and mannitol formulation was the more stable; with more of either, the hormone alone was. Water sorbed after drying generally acted like water left in by drying. Hsu and colleagues reported that year that excipient-free tissue plasminogen activator dried below its calculated water monolayer turned opalescent on reconstitution, while samples at monolayer or multilayer water tended to lose more biological stability under heat, and concluded that "the drier the better" may not hold for it.

Opening the vial: water from stoppers and air

A sorption isotherm records how much water a dried solid takes up at each humidity. Costantino and colleagues reported in 1994 that lyophilised insulin held at raised temperature and humidity aggregated covalently, through thiol-catalysed disulfide interchange, and non-covalently, with the extent of aggregation tracking its water uptake on the isotherm. Khomane and colleagues characterised NP-647, an amorphous three-residue analogue of thyrotropin releasing hormone, in 2011 as very hygroscopic and deliquescent, with a glass transition of 66.73 degrees C at 50 per cent relative humidity.

Sealed solids gained water too. Pikal and Shah found in 1992 that two amorphous solids under butyl rubber stoppers drew water from the stopper itself, approaching an apparent equilibrium with a half-time of about 10 months at 5 degrees C and about 4 days at 40 degrees C. Equilibrium water ran from 0.68 per cent, for 100 mg of lactose under the longest-dried stoppers, to 5.0 per cent for 25 mg of a highly hygroscopic glycopeptide antibiotic, and rose as the mass of solid per vial fell.

One page examined for this note stated, citing supplier handbooks that give no data, that peptides absorb moisture from the air, lowering peptide content and possibly stability, and that sequences rich in aspartic and glutamic acid, lysine, arginine or histidine take up the most. The first part matches the measurements above. For the second, the closest measurement located was Hsu's finding that two proteins' water monolayers agreed with counts of their strong polar groups; PubMed searches on 11 November 2026 pairing water sorption with side chains in peptide powders, or hygroscopicity with peptide salts, returned eight records in all, none measuring either.

Cake appearance: collapse, fogging and meltback

Schersch and colleagues produced collapsed and intact cakes of identical formulation in 2010 with a monoclonal antibody, a second pharmaceutical protein and lactate dehydrogenase, chosen for its sensitivity to freeze-drying, and quantified collapse as lost specific surface area. Collapsed cakes held comparable residual moisture, reconstituted no more slowly and showed no relevant difference in aggregation, activity or conformation. Wang, Hey and Nail reported in 2004 that collapse left the activity over time of recombinant factor VIII and alpha-amylase unchanged at 5 and 25 degrees C; at 40 degrees C the collapsed factor VIII, holding more residual moisture, appeared more stable.

Collapse that began in storage differed. Schersch and colleagues found in 2013 that an antibody was significantly better stabilised in cakes that collapsed during freeze-drying than in cakes that collapsed during storage at 40 or 50 degrees C, a difference they related to crystallisation and hydrolysis of the stabiliser and non-enzymatic browning. Schaal and colleagues reported in 2025 that a PEGylated peptide dried with sucrose and mannitol was markedly unstable at 50 degrees C, with cake collapse and browning, while a trehalose formulation stayed stable and spin-freezing conditions had no consistent effect on peptide or monomer levels.

Fogging, dried product coating the glass above the cake, is often considered cosmetic, with a possible risk to the seal if it reaches the neck; Langer and colleagues found in 2020 that vial types differing in fogging differed in no other cake property or quality attribute measured. Meltback, collapse from incomplete sublimation, is described in the inspection guide as bringing a change in physical form and a pocket of moisture that may raise instability; a PubMed search on 11 November 2026 for meltback returned 18 records, none measuring a meltback cake of a peptide or protein. How a cake dissolves is recorded in this site's note on reconstituting peptides.

A label line records a process; a certificate records a sample

A line naming the country where a product was lyophilised records where one process ran: the freeze-drying. Content, purity and water are recorded, when they are, on a certificate for a lot. One listing that states where its vial was lyophilised, for the tetrapeptide epitalon (Ala-Glu-Asp-Gly), prints "Lyophilized in the USA" and separately names a lot, EPX03, a test date of 17 July 2026 and an ISO/IEC 17025 accredited laboratory.

The World Health Organization's 2018 model certificate of analysis lists what a certificate carries: tests performed on a particular sample, each result against its acceptance criterion, a conclusion on compliance, the batch number, expiry or retest date, the original manufacturer and, where it covers the analysis, the laboratory's ISO/IEC 17025 accreditation. It describes a sample on the day it was tested. The inspection guide makes water part of finished-product testing for regulated lyophilised products, expecting moisture specifications backed by stability data at the limit.

What the pages claim, and what traces

Six pages returned by web searches on 11 November 2026 were examined for this note. Traced: the description of freeze-drying as freezing followed by drying under vacuum; that drying can slow degradation, consistent with rates that rose with water and qualified on three pages as compound-specific; that appearance cannot establish stability and that a collapsed cake does not prove degradation, as the collapse studies found; and, in part, that absorbed moisture lowers peptide content and stability, and that brown discolouration is a warning, since browning accompanied degradation in the sugar-containing cakes above. A residual moisture figure of under 1 to 3 per cent matched May's figure for most biological products, not the 5.0 per cent Pikal and Shah measured after stopper equilibration.

Untraced or contradicted: powder storage spans of days to months at room temperature, 6 months to more than 2 years refrigerated and about 1 year to several years at minus 20 degrees C, which disagreed and cited handbooks at most; a figure of 17 years, matched by no record in PubMed searches pairing it with lyophilised or freeze-dried peptides; that the powder lacks water and that hydrolysis stops or slows to near zero, against the guide's definition and the deamidation, isomerisation and oxidation measured in dried solids; that a solid cake signals quality and powder on the glass counts against a vial, which the collapse and fogging studies did not bear out for the proteins tested; and the residue claim above. In the measured record the dried solid held water, gained more from stoppers and air, and changed with that water, oxygen, temperature and formulation.

Disclosure. Vialog is published by the team behind Disguised Alpha, which sells the product linked in this note. The note follows the same editorial policy as every other page on this site.

References

  1. US Food and Drug Administration. Guide to inspections of lyophilization, July 1993 [inspection technical guide; title shortened]. Content current as of 11 November 2014. Sections read: introduction (freezing, primary drying by sublimation, secondary drying by desorption), glossary entry for lyophilization (the major portion of the water reduced by sublimation and desorption), finished product testing, stability testing (moisture specifications supported by stability data at the limit) and finished product inspection, meltback (collapse from incomplete sublimation; a change in physical form and a pocket of moisture that may result in greater instability). Guidance for investigators, not a study. No PMID. Retrieved 11 November 2026. View on fda.gov
  2. May JC, Wheeler RM, Etz N, Del Grosso A. Measurement of final container residual moisture in freeze-dried biological products. Dev Biol Stand. 1992;74:153-64. PMID 1592165 View on pubmed.ncbi.nlm.nih.gov
  3. Lai MC, Hageman MJ, Schowen RL, Borchardt RT, Topp EM. Chemical stability of peptides in polymers. 1. Effect of water on peptide deamidation in poly(vinyl alcohol) and poly(vinyl pyrrolidone) matrixes. J Pharm Sci. 1999;88(10):1073-80. doi:10.1021/js980227g. PMID 10514358 View on pubmed.ncbi.nlm.nih.gov
  4. Breen ED, Curley JG, Overcashier DE, Hsu CC, Shire SJ. Effect of moisture on the stability of a lyophilized humanized monoclonal antibody formulation. Pharm Res. 2001;18(9):1345-53. doi:10.1023/a:1013054431517. PMID 11683251 View on pubmed.ncbi.nlm.nih.gov
  5. Pikal MJ, Dellerman K, Roy ML. Formulation and stability of freeze-dried proteins: effects of moisture and oxygen on the stability of freeze-dried formulations of human growth hormone. Dev Biol Stand. 1992;74:21-37; discussion 37-8. PMID 1592171 View on pubmed.ncbi.nlm.nih.gov
  6. Hsu CC, Ward CA, Pearlman R, Nguyen HM, Yeung DA, Curley JG. Determining the optimum residual moisture in lyophilized protein pharmaceuticals. Dev Biol Stand. 1992;74:255-70; discussion 271. PMID 1592175 View on pubmed.ncbi.nlm.nih.gov
  7. Costantino HR, Langer R, Klibanov AM. Moisture-induced aggregation of lyophilized insulin. Pharm Res. 1994;11(1):21-9. doi:10.1023/a:1018981208076. PMID 8140052 View on pubmed.ncbi.nlm.nih.gov
  8. Khomane K, Kumar L, Meena CL, Jain R, Bansal A. NP-647, a novel TRH analogue: investigating physicochemical parameters [title shortened; the study characterised the solid and its solutions in vitro]. Int J Pharm. 2011;406(1-2):21-30. doi:10.1016/j.ijpharm.2010.12.025. PMID 21185925 View on pubmed.ncbi.nlm.nih.gov
  9. Pikal MJ, Shah S. Moisture transfer from stopper to product and resulting stability implications. Dev Biol Stand. 1992;74:165-77; discussion 177-9. PMID 1592166 View on pubmed.ncbi.nlm.nih.gov
  10. Schersch K, Betz O, Garidel P, Muehlau S, Bassarab S, Winter G. Systematic investigation of the effect of lyophilizate collapse on pharmaceutically relevant proteins I: stability after freeze-drying. J Pharm Sci. 2010;99(5):2256-78. doi:10.1002/jps.22000. PMID 20039389 View on pubmed.ncbi.nlm.nih.gov
  11. Wang DQ, Hey JM, Nail SL. Effect of collapse on the stability of freeze-dried recombinant factor VIII and alpha-amylase. J Pharm Sci. 2004;93(5):1253-63. doi:10.1002/jps.20065. PMID 15067701 View on pubmed.ncbi.nlm.nih.gov
  12. Schersch K, Betz O, Garidel P, Muehlau S, Bassarab S, Winter G. Systematic investigation of the effect of lyophilizate collapse on pharmaceutically relevant proteins III: collapse during storage at elevated temperatures. Eur J Pharm Biopharm. 2013;85(2):240-52. doi:10.1016/j.ejpb.2013.05.009. PMID 23727369 View on pubmed.ncbi.nlm.nih.gov
  13. Schaal Z, Bockstal PV, Lammens J, Lenger JH, Funke AP, Schneid SC, Beer T. Impact of spin-freezing parameters and excipient composition on product stability of a PEGylated peptide formulation. Int J Pharm. 2025;683:126007. doi:10.1016/j.ijpharm.2025.126007. PMID 40759220 View on pubmed.ncbi.nlm.nih.gov
  14. Langer C, Mahler HC, Koulov A, Marti N, Grigore C, Matter A, Chalus P, Singh S, Lemazurier T, Joerg S, Mathaes R. Method to Predict Glass Vial Fogging in Lyophilized Drug Products. J Pharm Sci. 2020;109(1):323-330. doi:10.1016/j.xphs.2019.08.024. PMID 31473212 View on pubmed.ncbi.nlm.nih.gov
  15. World Health Organization. Annex 4: Model certificate of analysis. In: WHO Expert Committee on Specifications for Pharmaceutical Preparations: fifty-second report. WHO Technical Report Series, No. 1010. Geneva: World Health Organization; 2018. p. 187-191. Contents listed for a certificate read: tests performed on a particular sample with results, acceptance criteria and a compliance conclusion; batch number; expiry or retest date; date of manufacture where available; original manufacturer; reference to ISO/IEC 17025 accreditation where related to the analysis. Guidance, not a study. No PMID. Retrieved 11 November 2026. View on extranet.who.int